Tile Adhesive/Superpaste/Bonding Liquid/Keying Agent/Self Levelling Screed
GET IN TOUCH FOR ANY PRICING REQUESTS, QUOTATIONS OR ENQUIRIES
Tiles 4 All offers a wide selection of Adhesives, Grouts, Bonding Liquid, Keying Agent, Porcelain Adhesives, Fast Drying Adhesives, Superpaste & Self Levelling Screed plus Technical information on various products.
- WHITE PORCELAIN PROFIX 20KG
- UNIVERSAL TILE LIGHTWEIGHT ADHESIVE
- UNDER-FLOOR HEATING SCREED 20KG
- TILE STAIN FREE GROUT 20KG
- TILE STAIN FREE GROUT 5KG
- SURFACE KEY COMPOUND 20KG
- SUREFIX TILE ADHESIVE 20KG
- SUPER GRIP PASTE 1,2& 5 KG BUCKETS
- SELF LEVELLING SCREED 20KG
- PROSKIM POOL PLASTER
- SUPER GRIP PASTE 1,2,&5 KG BUCKETS
- MOSAIC PROFIX TILE ADHESIVE 20KG
- PROFIX TILE ADHESIVE 20KG
- BONDING AGENTS
- LIGHT WEIGHT PORCELAIN PROFIX 24
- LIGHT WEIGHT PORCELAIN PROFIX 12
- LIGHT WEIGHT PORCELAIN PROFIX 6
- KEYING AGENTS
- ILEVEL PRO SCREED
- PORCELAIN PROFIX 24 TILE ADHESIVE
- PORCELAIN PROFIX 12 TILE ADHESIVE
- PORCELAIN PROFIX 6 HOUR DRYING
- PORCELAIN PROFIX TILE ADHESIVE 2 HOUR DRYING
- GENERAL PURPOSE TILE GROUT
- RAPID REPAIR AND ANCHORING CEMENT 20KG
- PORCELAIN PROFIX TILE ADHESIVE 6 HOUR DRYING
- CORNICE ADHESIVE 1,2&5 KG BUCKETS
- BONDING AGENTS
- MOSAIC FIX 535 5KG BAGS
- MULTI TILE ADHESIVE LIGHT WEIGHT 500 15 KG BAGS
- MULTI TILE ADHESIVE 510 LIGHT WEIGHT 15 KG BAGS
- MULTI TILE ADHESIVE 520 20 KG BAGS
- MULTI TILE ADHESIVE 530 20 KG BAGS
TYL-PRO Flexible Porcelain Profix 6 Hour Tile Adhesive
DESCRIPTION & PURPOSE
TYL-PRO Flexible Porcelain Profix 6 Hour Tile Adhesive is a multi purpose rapid hardening grey cement-based adhesive. Suited for use in interior and exterior conditions, walls and floors, thin and medium bed applications. Can be used for the fixing of porcelain, mosaic, ceramic, stone, brick and clay tiles to cement render, screeds, concrete and primed fibre cement surfaces. Ideal for tiling directly onto smooth, powerfloated, suspended, impervious surfaces and tiling directly onto existing tiles.
CAUTIONS & RECOMMENDATIONS
This product is not recommended for use on white or light-coloured highly absorbent tiles as it might cause staining. For installation of the above mentioned tiles the use of TYL-PRO White Porcelain Profix 6 Hour Tile Adhesive is recommended.
CURING/ SETTING PERIODS
(SABS Code of practice for the Design and Installation of Ceramic Tiles Code 0107 – 1996)
- New concrete floors – 6 weeks curing time prior to tiling can commence.
- New concrete floors – 4 weeks curing time before screeding and
- Screeds – Additional 4 weeks before tiling can commence.
- New brick walls – 6 weeks curing time before direct bedding.
- New brick walls – 4 weeks curing time before plastering and
- Plaster – Additional 2 weeks before tiling can commence.
- RECOMMENDATION – Wood floated surfaces are ideal for tiling.
SURFACE PREPARATION/ CONDITIONS
1. Application surfaces must be solid/firm and free of dust, mould oil, grease, sealers, wax polish, bitumen, paint, gypsum and organic growth. Organic growth must be removed and the spores killed with an effective fungicide such as a household bleaching solution.
2. Painted and Gypsum-plastered surfaces need to be chipped to minimum 80% to remove the paint or Gypsum.
3. Enamel-painted and bitumen surfaces: Strip all of the coating by scraping and then chip to expose minimum 80% of the application substrate. DO NOT USE A SOLVENT BASED PRODUCT OR HEAT (HEATING TORCH) TO REMOVE BITUMEN FROM THE SUBSTRATE.
4. Existing ceramic tiles surfaces: Clean thoroughly with undiluted TYL-PRO Tile Cleaner. Leave on the application surface for minimum 5 minutes to re-act. Rinse thoroughly with cold clean water to neutralize the acid. Allow to dry completely before tiling commences.
TYL-PRO Porcelain Profix 24 Tile Adhesive
DESCRIPTION & PURPOSE
TYL-PRO Porcelain Profix 24 Tile Adhesive is a multi purpose rapid hardening cement-based adhesive. Suited for use in interior and exterior conditions, walls and floors, thin and medium bed applications. Can be used for the fixing of porcelain, natural stones, mosaic, ceramic, stone, brick and clay tiles to cement render, screeds, concrete and primed fibre cement surfaces.
CAUTIONS & RECOMMENDATIONS
This product is not recommended for use on white or light-coloured highly absorbent tiles as it might cause staining. For installation of the above mentioned tiles the use of TYL-PRO White Porcelain Profix 24 Adhesive is recommended.
CURING/ SETTING PERIODS
(SABS Code of practice for the Design and Installation of Ceramic Tiles Code 0107 – 1996)
- New concrete floors – 6 weeks curing time prior to tiling can commence.
- New concrete floors – 4 weeks curing time before screeding and
- Screeds – Additional 4 weeks before tiling can commence.
- New brick walls – 6 weeks curing time before direct bedding.
- New brick walls – 4 weeks curing time before plastering and
- Plaster – Additional 2 weeks before tiling can commence.
- RECOMMENDATION – Wood floated surfaces are ideal for tiling. For power floated/ steel trowelled surfaces and tiling onto existing tiles follow step 5 below under the paragraph surface preparation/ conditions.
SURFACE PREPARATION/ CONDITIONS
1. Application surfaces must be solid/firm and free of dust, mould oil, grease, sealers, wax polish, bitumen, paint, gypsum and organic growth. Organic growth must be removed and the spores killed with an effective fungicide such as a household bleaching solution.
2. Painted and Gypsum-plastered surfaces need to be chipped to minimum 80% to remove the paint or Gypsum.
3. Enamel-painted and bitumen surfaces: Strip all of the coating by scraping and then chip to expose minimum 80% of the application substrate. DO NOT USE A SOLVENT BASED PRODUCT OR HEAT (HEATING TORCH) TO REMOVE BITUMEN FROM THE SUBSTRATE.
4. Existing ceramic tiles surfaces: Clean thoroughly with undiluted TYL-PRO Tile Cleaner. Leave on the application surface for minimum 5 minutes to re-act. Rinse thoroughly with cold clean water to neutralize the acid. Allow to dry completely before tiling commences.
5. Smooth, off-form/shutter or power-floated cement surfaces: Acid wash to remove laitance, rinse well with cold clean water to neutralize the acid. NOTE: Allow to dry completely before tiling commences.
NOTE: Once the surface preparation has been completed on the above problem surfaces, the area must be primed with TYL-PRO Surface Key Compound mixed with TYL-PRO Keying agent. (Two parts of TYL-PRO Surface Key Compound to be mixed with one part of TYL-PRO Keying Agent and applied with a builder block brush to a thickness of ± 2mm and allowed to dry for 24 hours.)
MIXING INSTRUCTIONS
1. Mix 20kg of TYL-PRO Porcelain Profix 24 Tile Adhesive to ± 5 litres of cold clean water. In wet, permanently wet tiling conditions or suspended slabs completely replace the water in the mix with TYL-PRO Bonding Agent.
2. Mix to a creamy smooth paste. Mechanical mixing will result in a lump free, easier to use mix.
3. Allow mix to activate for 5 minutes.
4. Remix product before use. DO NOT ADD MORE WATER.
5. Do not mix more adhesive than can be used within ± 1 hour.
APPLICATION PROCEDURE
1. Spread enough adhesive with a notched Wall or Floor trowel to a minimum bedded thickness of:
- 3 mm for wall tiling and 6 mm for floor tiling.
- Heavily lugged, grooved or dovetailed tiles must be buttered to fill any voids with adhesive before placing into wet adhesive.
2. Press tiles firmly into wet adhesive with a twisting action. Use a rubber mallet to bed large or heavy tiles.
3. Occasionally lift a tile to check that full contact is being made between the tile and the wet adhesive.
- Remove excess adhesive from joints and tiled surface before drying has occurred. Minimum grouting joints for walls is 2 mm and for floors 3 mm or as recommended by the tile manufacturer.
- Do not butt joint tiles.
4. Tiles must be allowed to dry for maximum 6 hours before grouting takes place. (For sealed or non-porous surfaces allow minimum 24 hours)
- GROUTING: Ensure that the joints are free from tile adhesive and any other foreign matter.
- Use TYL-PRO General Purpose Tile Grout. (For sealed or non-porous surfaces allow 48 hours.)
5. In wet, permanently wet conditions and suspended slabs replace the water in the mix with TYL-PRO Bonding Agent.
TYL-PRO Self Levelling Screed
DESCRIPTION & PURPOSE
TYL-PRO Self levelling Screed is a rapid hardening grey cement-based self levelling compound. Suited for use in interior and exterior conditions. This product can be used as a smoothing, levelling and repair compound on light duty wearing surfaces.
CAUTIONS & RECOMMENDATIONS
This product is not recommended for use in heavy duty conditions. For harder wearing surfaces or when under-floor heating is installed the product should be mixed with TYL-PRO Bonding Agent.
CURING/ SETTING PERIODS
(SABS Code of practice for the Design and Installation of Ceramic Tiles Code 0107 – 1996)
- New concrete floors – 6 weeks curing time prior to tiling can commence.
- New concrete floors – 4 weeks curing time before screeding and
- Screeds – Additional 4 weeks before tiling can commence.
- New brick walls – 6 weeks curing time before direct bedding.
- New brick walls – 4 weeks curing time before plastering and
- Plaster – Additional 2 weeks before tiling can commence.
- RECOMMENDATION – Wood floated surfaces are ideal for tiling. For power floated/ steel trowelled surfaces and tiling onto existing tiles follow step 8 below under the paragraph surface preparation/ conditions.
SURFACE PREPARATION/ CONDITIONS
1. Application surfaces must be solid/firm and free of dust, mould oil, grease, sealers, wax polish, bitumen, paint, gypsum and organic growth. Organic growth must be removed and the spores killed with an effective fungicide such as a household bleaching solution.
2. Painted and Gypsum-plastered surfaces need to be chipped to minimum 80% to remove the paint or Gypsum.
3. Enamel-painted and bitumen surfaces: Strip all of the coating by scraping and then chip to expose minimum 80% of the application substrate. DO NOT USE A SOLVENT BASED PRODUCT OR HEAT (HEATING TORCH) TO REMOVE BITUMEN FROM THE SUBSTRATE.
4. Existing ceramic tiles surfaces: Clean thoroughly with undiluted TYL-PRO Tile Cleaner. Leave on the application surface for minimum 5 minutes to re-act. Rinse thoroughly with cold clean water to neutralize the acid. Allow to dry completely before tiling commences. Remove all loose tiles prior to screeding.
5. Porous surfaces/substrates should be dampened prior to applying TYL-PRO Self levelling Screed.
TYL-PRO Concentrate Bonding Agent
DESCRIPTION & PURPOSE
TYL-PRO Concentrate Bonding Agent is latex based liquid, specially formulated to be used in conjunction with TYL-PRO Cement-Based Adhesive and TYL-PRO Tile Grouts where complicated application, high traffic areas, permanently wet conditions exist, additional flexibility or increased bond strength is required. TYL-PRO Bond Concentrate is also a primer for the sealing and stabilizing of friable and chalking surfaces, both interior and exterior prior to tiling or coating.
SURFACE PREPARATION/ CONDITIONS
1. Application surfaces must be solid/firm and free of dust, mould oil, grease, sealers, wax polish, bitumen, paint, gypsum and organic growth. Organic growth must be removed and the spores killed with an effective fungicide such as a household bleaching solution.
2. Painted and Gypsum-plastered surfaces need to be chipped to minimum 80% to remove the paint or Gypsum.
3. Enamel-painted and bitumen surfaces: Strip all of the coating by scraping and then chip to expose minimum 80% of the application substrate. DO NOT USE A SOLVENT BASED PRODUCT OR HEAT (HEATING TORCH) TO REMOVE BITUMEN FROM THE SUBSTRATE.
4. Existing ceramic tiles surfaces: Clean thoroughly with undiluted TYL-PRO Tile Cleaner. Leave on the application surface for minimum 5 minutes to re-act. Rinse thoroughly with cold clean water to neutralize the acid. Allow to dry completely before tiling commences.
5. Smooth, off-form/shutter or power-floated cement surfaces: Acid wash to remove laitance, rinse well with cold clean water to neutralize the acid. NOTE: Allow to dry completely before tiling commences.
APPLICATION PROCEDURE – SHAKE WELL BEFORE USE
1. Replace water in the mix with TYL-PRO Bonding Agent when using TYL-PRO Cement-Based Adhesives and TYL-PRO General Purpose Tile Grouts in the following areas: Heavy duty environments, permanently wet areas, abattoirs, breweries, hospitals, dairies, smooth trowelled wall and floor areas, cold rooms and walls where temperature changes are experienced.
2. TYL-PRO Bonding Agent can also be used as a priming/sealing coat for Gypsum, asbestos and cement surfaces. When used as a primer/sealer, brush on TYL-PRO Bonding Agent until surface is saturated. Leave to dry for a minimum of 1 hour and a maximum of 48 hours before tiling or coating.
CURING/ SETTING PERIODS
No curing is required.
NOTE
Cement or cement-based adhesives and grouts will dry a shade darker with the addition
of TYL-PRO Bonding Agent. These products will also take approximately 12 hours
longer to dry.
APPLICATION COVERAGE
Refer to application product used along with TYL-PRO Bonding Agent. When used as
a primer/sealer, 5 litres TYL-PRO Bonding Agent will cover approximately 25 – 30m²
depending on the nature of the surface. (1 Coat application)
PRODUCT GUARANTEE
We guarantee that TYL-PRO products meet the product specifications, performance and will be
free from any defect. All guarantees with regard to the performance of TYL-PRO products will
be subject to the professional, practical application and application conditions of TYL-PRO
products in accordance with our instructions, specifications and recommendations. However, we
have no influence over specific site conditions, applicators and therefore, if in doubt, the user
should first carry out sufficient tests to ensure that the product is suitable for intended
applications. In special cases or if the applicator is in doubt, obtain advice and an installation
specification. Should our product prove defective, we undertake to replace any defective material,
however we must be afforded the opportunity to investigate. This guarantee will fall away or will
be forfeited in the event of TYL-PRO products being contaminated or adulterated by the addition
of sand, cement or any substance other than recommended by us.
PRECAUTIONS / WARNINGS
- Do not empty products into drains.
- Do not ingest or inhale and keep away from children and pets.
- Do not use cement based products in temperatures below + 5 °C.
- Be careful when cement based products are used over + 30°C – skinning will occur. Area to be tiled must be shielded.
- Do not use icy water when mixing cement based products, especially in winter.
- Do not use hot water when mixing cement based products, especially in summer.
- Do not apply cement based products to freezing cold floors – + 5 °C and below.
SAFETY PRECAUTIONS
- Use as directed.
- Use a dust mask.
- Wear rubber gloves.
- Wear safety goggles.
- Do not ingest or inhale.
- Work in well ventilated areas.
- In the event of contamination rinse thoroughly with cold water.
- Seek medical assistance if irritation or discomfort persists.
TYL-PRO Surface Key Compound
DESCRIPTION & PURPOSE
TYL-PRO Surface Key Compound is a multi purpose rapid hardening water resistant cement-based primer for the use on previously painted surfaces, smooth and dense surfaces and used as a waterproofing primer in swimming pools, showers, balconies etc. Suited for use in interior and exterior conditions, walls and floors. The product must be mixed with TYL-PRO Keying Agent and allowed 24 hours to dry prior to tile application.
CURING/ SETTING PERIODS
(SABS Code of practice for the Design and Installation of Ceramic Tiles Code 0107 – 1996)
- New concrete floors – 6 weeks curing time prior to tiling can commence.
- New concrete floors – 4 weeks curing time before screeding and
- Screeds – Additional 4 weeks before tiling can commence.
- New brick walls – 6 weeks curing time before direct bedding.
- New brick walls – 4 weeks curing time before plastering and
- Plaster – Additional 2 weeks before tiling can commence.
- RECOMMENDATION – Wood floated surfaces are ideal for tiling. For power floated/ steel trowelled surfaces and tiling onto existing tiles follow step 5 below under the paragraph surface preparation/ conditions.
SURFACE PREPARATION/ CONDITIONS
1. Application surfaces must be solid/firm and free of dust, mould oil, grease, sealers, wax polish, bitumen, paint, gypsum and organic growth. Organic growth must be removed and the spores killed with an effective fungicide such as a household bleaching solution.
2. Painted and Gypsum-plastered surfaces need to be chipped to minimum 80% to remove the paint or Gypsum.
3. Enamel-painted and bitumen surfaces: Strip all of the coating by scraping and then chip to expose minimum 80% of the application substrate. DO NOT USE A SOLVENT BASED PRODUCT OR HEAT (HEATING TORCH) TO REMOVE BITUMEN FROM THE SUBSTRATE.
4. Existing ceramic tiles surfaces: Clean thoroughly with undiluted TYL-PRO Tile Cleaner. Leave on the application surface for minimum 5 minutes to re-act. Rinse thoroughly with cold clean water to neutralize the acid. Allow to dry completely before tiling commences.
5. Smooth, off-form/shutter or power-floated cement surfaces, balconies, swimming Pools and showers: Acid wash to remove laitance, rinse well with
- 2 -
cold clean water to neutralize the acid. NOTE: Once the surface preparation has been completed on the above problem surfaces, the area must be primed with TYL-PRO Surface Key Compoundmixed with TYL-PRO Keying agent. (Two parts of TYL-PRO Surface Key Compound to be mixed with one part of TYL-PRO Keying Agent and applied with a builder block brush to a thickness of ± 2mm and allowed to dry for 24 hours.)
MIXING INSTRUCTIONS
1. Mix 20kg of TYL-PRO Surface Key Compound to ± 7.0 litres of TYL-PRO Keying Agent or 5 kg of TYL-PRO Surface Key Compound to approximately 1,75 litres of TYL-PRO Keying Agent.
2. Mix to a creamy smooth paintable paste. Mechanical mixing will result in a lump free, easier to use mix.
3. Allow mix to activate for 5 minutes.
4. Remix product before use.
5. Do not mix more compound than can be used within ± 1 hour.
APPLICATION PROCEDURE
1. Apply TYL-PRO Surface Key Compound with a builders block brush ± 2mm thick and allowed the primer to dry for 24 hours prior to applying any surface covering.
TECHNICAL SPECIFICATIONS
Non-hazardous Non-flammable, freeze and thaw resistant
Initial setting time ± 6 hours at 25 °C and 50% humidity
Final setting time ± 24 hours at 25 °C and 50% humidity
Open time ± 20 – 25 minutes at 25 °C and 50% humidity
Pot life ± 1 -1.5 hours at 25 °C and 50% humidity
Temperature Resistant up to 90 °C
Mixed weight 1,8 kg per litre
Shelf life 6 months in dry moderate conditions
Storage Store in dry conditions on Pallets
Coverage per 20 kg ± 15 – 20 m² at 1.5mm thickness
Coverage per 5 kg ± 3 – 5 m² at 1.5mm thickness
(The above is calculated on an even, level surface and application thickness)
Packaging 20 kg & 5 kg
Application Temperature + 5 °C to + 30°C.
TYL-PRO Super Grip Paste Tile Adhesive – DIY
DESCRIPTION & PURPOSE
TYL-PRO Super grip Paste Tile Adhesive is a ready mixed, thin bed, paste adhesive. Suited for use in interior conditions – walls and floors. Can be used for fixing lightweight ceramic, brick, Mosaic, Stone and clay tiles to plaster, concrete, primed cement fibre board. This product cannot be used in areas prone to moisture i.e. Bathrooms
CAUTIONS & RECOMMENDATIONS
This product is not recommended for use in wet, permanently wet conditions or in swimming pools. This product is not suitable for tiling onto flexible surfaces- Use TYL-PRO Super grip Paste Tile Adhesive.
CURING/ SETTING PERIODS
(SABS Code of practice for the Design and Installation of Ceramic Tiles Code 0107 – 1996)
- New concrete floors – 6 weeks curing time prior to tiling can commence.
- New concrete floors – 4 weeks curing time before screeding and
- Screeds – Additional 4 weeks before tiling can commence.
- New brick walls – 6 weeks curing time before direct bedding.
- New brick walls – 4 weeks curing time before plastering and
- Plaster – Additional 2 weeks before tiling can commence.
- RECOMMENDATION – Wood floated surfaces are ideal for tiling. For power floated/ steel trowelled surfaces and tiling onto existing tiles follow step 6 below under the paragraph surface preparation/ conditions.
SURFACE PREPARATION/ CONDITIONS
1. Surfaces must be solid/firm and free of dust, mould oil, grease, sealers, wax polish and organic growth. Organic growth must be removed and the spores killed with an effective fungicide such as a household bleaching solution.
2. At least one of the surfaces should be absorbent i.e. back of tile or the substrate.
3. Painted and Gypsum-plastered surfaces need to be chipped to remove 80% of the paint or Gypsum.
4. Enamel-painted and bitumen surfaces: Strip all of the coating by scraping and then chip to expose 80% of the substrate. DO NOT USE A SOLVENT OR HEAT TO REMOVE BITUMEN FROM THE SUBSTRATE.
5. Existing ceramic tiles: Clean thoroughly with undiluted TYL-PRO Tile Cleaner.
Rinse thoroughly with cold clean water. Allow to dry before tiling commences.
6. Smooth, off-form/shutter or power-floated cement surfaces: Acid wash to remove laitance, rinse well with cold clean water. NOTE: Once the surface preparation has been completed on the above problem surfaces, the area must be primed with TYL-PRO Surface Key Compound mixed with TYL-PRO Keying Agent. (Two parts of TYL-PRO Surface Key Compound to be mixed with one part of TYL-PRO Keying Agent and applied with a builder block brush to a thickness of ± 2mm and allowed to dry for 24 hours.)
MIXING INSTRUCTIONS
1. TYL-PRO Supergrip Paste Tile Adhesive is a ready to use paste adhesive and must not be adulterated by addition of water or any other substance.
2. Stir product before use. DO NOT ADD WATER.
APPLICATION PROCEDURE
- Apply a 3 mm bed of adhesive using a 6 mm x 6 mm x 6 mm notched trowel.
1. Spread enough adhesive with a notched Wall or Floor trowel to a minimum bedded thickness of:
- 3 mm for wall and floor tiling.
- Heavily lugged, grooved or dovetailed tiles must be buttered to fill any voids with adhesive before placing into wet adhesive.
- Do not spread more adhesive than can be used within ± 10 minutes.
2. Press tiles firmly into wet adhesive with a twisting action. Use a rubber mallet to bed large or heavy tiles.
3. Occasionally lift a tile to check that full contact is being made between the tile and the wet adhesive.
4. Remove excess adhesive from joints and tiled surface before drying has occurred. Minimum grouting joints for walls is 2 mm and for floors 3 mm or as recommended by the tile manufacturer.
- Do not butt joint tiles.
5. Tiles must be allowed to dry for minimum 24 hours before grouting takes place. (For sealed or non-porous surfaces allow minimum 48 hours)
- GROUTING: Ensure that the joints are free from tile adhesive and any other foreign matter.
- Use TYL-PRO General Purpose Tile Grout. (For sealed, primed or non-porous surfaces allow 48 hours drying time.)